TTF Factory Panerai Luminor Marina PAM01116 Pre-Shipment QC Review

TTF Factory Panerai Luminor Marina PAM01116 Pre-Shipment QC Review

The TTF Factory Panerai Luminor Marina PAM01116 combines a 44mm steel case, olive green dial, Arabic numeral layout and leather strap, together with a P.9010 movement and sapphire crystal.

This version is particularly worth considering for Panerai references that may not be available from VS Factory. Rather than focusing only on the factory name, the individual watch should be evaluated through its actual movement readings, dimensions, exterior finishing and functional QC.

During this pre-shipment test, the P.9010 movement recorded +18 seconds/day, 295° amplitude, 0.1ms beat error and 28,800 BPH.

The specific watch measured 44mm in width, 16.3mm in thickness and 144.5g in weight.

QC Test Results

Inspection Item Measured Result
Factory TTF Factory
Model Panerai Luminor Marina PAM01116
Dial Olive Green
Hour Markers Arabic Numerals
Case Steel
Strap Leather
Movement P.9010
Daily Rate +18 s/day
Amplitude 295°
Beat Error 0.1ms
Beat Rate 28,800 BPH
Crystal Sapphire Crystal
Measured Width 44mm
Measured Thickness 16.3mm
Measured Weight 144.5g

These figures represent the actual measurements of this specific QC sample. Minor variations may occur between individual watches due to power reserve, production tolerances, testing position and measurement methods.

P.9010 Movement Performance

This TTF Factory PAM01116 is equipped with a P.9010 movement.

The timegrapher recorded:

Daily Rate: +18 seconds/day
Amplitude: 295°
Beat Error: 0.1ms
Beat Rate: 28,800 BPH

The 295° amplitude indicates that the movement was operating with a strong power state during this particular test, while the 0.1ms beat error was well controlled.

The daily rate, however, measured +18 seconds/day.

Using a typical pre-shipment QC reference of approximately ±0–15 seconds/day, this particular sample is slightly outside that preferred range. The practical approach would be to regulate the movement and perform another timegrapher test before shipment rather than treating the reading as a permanent characteristic of the model.

This is also a useful example of why individual QC is important even when the overall watch quality is good.

44mm Case Size

This specific PAM01116 measured 44mm in width.

The 44mm case is an important part of the traditional Luminor wrist presence, particularly when combined with the recognizable crown-protection structure.

For buyers comparing different Panerai versions, actual width should be considered together with thickness and weight because all three measurements influence how substantial the watch feels on the wrist.

16.3mm Measured Thickness

The actual measured thickness is 16.3mm.

This is a relatively substantial case profile and should be considered when evaluating the overall wearing experience.

A Panerai can look similar from a straight-on photograph even when different versions have noticeably different case profiles. For this reason, actual thickness measurement is useful when comparing factory versions.

The 16.3mm figure applies to this specific QC sample.

144.5g Measured Weight

This specific watch measured 144.5g.

Because this configuration uses a steel case with a leather strap, the total weight should not be directly compared with a full-steel bracelet watch without considering the different construction.

Weight alone is also not an indicator of overall quality. Case proportions, movement, dial finishing, strap construction and weight distribution should be considered together.

The 144.5g measurement provides a real-world reference for this individual watch.

Olive Green Dial and Arabic Numerals

The olive green dial is one of the defining visual characteristics of the PAM01116.

The dial should be inspected under different lighting conditions because green tones can change considerably depending on the light source, camera exposure and viewing angle.

During QC, particular attention should be given to the Arabic numerals, hour markers, hands, printing and overall alignment.

For a relatively clean Panerai dial layout, even small inconsistencies can become visually noticeable, making close-up inspection useful.

Sapphire Crystal and Steel Case

This version is fitted with a sapphire crystal.

Exterior QC should cover the crystal condition, steel case surfaces, bezel, crown-protection structure, crown, dial, hands and strap connection.

The crown guard is a particularly recognizable part of the Luminor design, so its operation and alignment should also be physically checked rather than evaluated only from photographs.

Leather Strap QC

This PAM01116 uses a leather strap.

The strap should be inspected around the stitching, edges, buckle and attachment points.

Because leather is a natural material, minor texture differences can occur. More important during QC is whether the strap is assembled correctly, securely attached and free from significant surface damage.

The buckle should also be opened and closed to confirm normal operation.

TTF Factory as an Alternative

For Panerai models where multiple factory versions are available, it is useful to compare the actual watch rather than assuming that one factory name automatically determines the quality of every reference.

For some Panerai references that are not available from VS Factory, TTF Factory provides another option worth examining.

Based on this PAM01116 sample, the overall construction and details are good. The main point requiring attention on this particular watch is the +18 seconds/day rate, which would benefit from regulation and retesting before shipment.

This distinction is important: the movement’s current daily rate is an individual QC issue that can potentially be adjusted, rather than evidence that the entire TTF version has the same timekeeping result.

Overall QC Assessment

This TTF Factory Panerai Luminor Marina PAM01116 recorded:

+18 seconds/day
295° amplitude
0.1ms beat error
28,800 BPH

Actual physical measurements were:

Width: 44mm
Thickness: 16.3mm
Weight: 144.5g
Crystal: Sapphire
Movement: P.9010

The overall quality and exterior execution of this version are good, and TTF Factory can be a useful alternative for certain Panerai references that are unavailable from VS Factory.

The 295° amplitude and 0.1ms beat error are good readings from this particular test. However, the +18 seconds/day daily rate is slightly higher than the preferred ±0–15 seconds/day QC reference, so this individual movement would ideally be regulated and tested again before shipment.

This is exactly where pre-shipment QC provides practical value: a good overall version can still have an individual watch that requires a small adjustment before approval.

FAQ | TTF Factory Panerai PAM01116

What movement does the TTF Factory PAM01116 use?
This specific QC sample is equipped with a P.9010 movement running at 28,800 BPH.

What were the timegrapher results?
The movement recorded +18 seconds/day, 295° amplitude, 0.1ms beat error and 28,800 BPH.

Is +18 seconds/day acceptable?
It is slightly above the commonly used ±0–15 seconds/day pre-shipment QC reference. For this individual watch, regulation followed by another timegrapher test would be preferable before shipment.

What are the actual dimensions?
This specific watch measured 44mm in width and 16.3mm in thickness.

How much does this PAM01116 weigh?
The measured weight of this specific QC sample is 144.5g.

Is TTF Factory worth considering if VS Factory does not make the model?
For Panerai references that are unavailable from VS Factory, TTF Factory can provide another option to compare. The most useful approach is to evaluate the individual watch’s movement readings, dimensions, dial, case finishing and functional QC rather than choosing solely by factory name.